Ford repair professionals: April 2012

2005 Dodge Ram Drive Belt Routing Diagrams?

The Drive belt or Serpentine belt Routing Diagram.

The Diagrams Shown Covers Dodge Ram 1500, 2500, 3500, 2WD & 4WD. Its For 2001 – 2005 Year Models.

Drive Belt Routings

The belt routing schematics are published from the latest information available at the time of publication. If anything differs between these schematics and the Belt Routing Label, use the schematics on Belt Routing Label. This label is located in the engine compartment.

Fig. Accessory serpentine belt routing-3.7L and 4.7L gasoline engines

Fig. Accessory serpentine belt routing-3.9L, 5.2L and 5.9L LDC gasoline engines

Fig. Accessory serpentine belt routing: Alternator (1), idler pulley (2), P/S pump (3), A/C compressor (4), crankshaft (5), belt tensioner (6) and water pump (7)-5.7L engine

Fig. Accessory serpentine belt routing-5.9L HDC and 8.0L gasoline engines with A/C

Fig. Accessory serpentine belt routing-5.9L HDC and 8.0L gasoline engines without A/C

use the schematics on Belt Routing Label. This label is located in the engine compartment.

Fig. Accessory serpentine belt routing-2001-03 5.9L Diesel engines with A/C

Accessory serpentine belt routing-2001-03 5.9L Diesel engines with A/C

Fig. Accessory serpentine belt routing-2001-03 5.9L Diesel engines without A/C

Fig. Accessory serpentine belt routing-2004-05 5.9L Diesel engines with A/C

Fig. Accessory serpentine belt routing-2004-05 5.9L Diesel engines without A/C

Fig. Accessory serpentine belt routing-A/C compressor (1), Without A/C (2), Power Steering Pump (3), Water Pump (4), Crankshaft Pulley (5), Auto tensioner (6), Alternator (7), Idler pulley (8)

Recommend Help links to view :----

These details will help.

Thanks.

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

Accessory Drive Belts Details on 2005 Dodge Ram?

The Complete Procedure to adjust and inspect drive belts.

The Procedure mentioned Covers Dodge Ram 1500, 2500, 3500, 2WD & 4WD. Its For 2001 – 2005 Year Models.

The Procedure is as follows:---

Adjustment

Belt tension is not adjustable. Belt adjustment is maintained by an automatic (spring load) belt tensioner.
The belts used on these vehicle are equipped with automatic (spring load) tensioners which maintain tension. No adjustment is necessary or possible.

Belt Tension Inspection

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.

These details will help.

Thanks.

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

Suspension Wheel Hub & Bearings Replacing on 2005 Dodge RAM?

The Procedure to remove/ install Wheel Hub and Bearings.

The to Adjust and replace.

The Procedure mentioned Covers Dodge Ram 1500, 2500, 3500, 2WD & 4WD. Its For 2001 – 2005 Year Models.

The Procedure is as follows:---

Adjustment

2001-02 Vehicles

Tighten the wheel bearing nut to 30-40 ft. lbs. (41-54 Nm) while turning the rotor.

Loosen the wheel bearing adjusting nut completely.

Tighten the nut finger-tight.

Check the wheel bearing end-play. The specification is 0.001-0.003 inch (0.025-0.076mm).

Install the nut lock and cotter pin.

2003-05 Models

These are unitized hub/bearing assemblies. No adjustment is possible.

Removal & Installation

2001-02 Vehicles
2wd Models

Before servicing the vehicle, refer to the Precautions Section.

Remove or disconnect the following:

Front wheel
Brake caliper
Grease cap
Cotter pin
Adjusting nut
Washer
Outer bearing
Brake rotor and hub assembly
Grease seal
Inner bearing

To install:

Install or connect the following:

Inner bearing
Grease seal
Brake rotor and hub assembly
Outer bearing
Washer
Adjusting nut. Adjust the bearings.
Cotter pin
Grease cap
Brake caliper
Front wheel

4wd Models

Remove or disconnect the following:

Front wheel
Brake caliper and rotor
Hub retainer nut
Hub and bearing assembly

To install:

Install or connect the following:

Hub and bearing assembly. Tighten the bolts to 125 ft. lbs. (170 Nm).
Hub retainer nut. Tighten the nut to 175 ft. lbs. (237 Nm).
Brake caliper and rotor
Front wheel

2003-05 Models
Coil Spring Suspension-2wd

Remove or disconnect the following:

Front wheel
Brake caliper and rotor
Wheel speed sensor
Hub/bearing mounting bolts
Hub/bearing assembly

To install:

Install or connect the following:

Hub and bearing assembly. Tighten the bolts to 120 ft. lbs. (163 Nm).
Wheel speed sensor
Brake caliper and rotor
Front wheel

Coil Spring Suspension-4wd

Remove or disconnect the following:

Front wheel
Brake caliper and rotor
Wheel speed sensor
Halfshaft nut
Tie rod end from the knuckle
Upper ball joint from the knuckle
Knuckle from the halfshaft
Hub/bearing mounting bolts
Hub/bearing assembly

To install:

Install or connect the following:

Hub and bearing assembly. Tighten the bolts to 120 ft. lbs. (163 Nm).
Knuckle onto the halfshaft
Upper ball joint on the knuckle. Torque the nut to 40 ft. lbs. (54 Nm) (on 1500 series, plus 90 degrees).
Tie rod end to the knuckle. Tighten the nut to 45 ft. lbs. (61 Nm) plus 90 degrees.
Halfshaft nut. Torque to 185 ft. lbs. (251 Nm).
Wheel speed sensor
Brake caliper and rotor
Front wheel

Coil/Link Suspension.

Remove or disconnect the following:

Front wheel
Hub extension from the rotor, if equipped
Brake caliper and rotor
Hub nut
Wheel speed sensor wiring
Hub/bearing mounting bolts ¹ / ₄ each. Then, tap the bolts with a mallet to loosen the hub/bearing assembly.
Hub/bearing assembly, wheel studs/extension studs, rotor, shield and spacer
Wheel speed sensor

To install:

Install or connect the following:

Wheel speed sensor
Rotor on the hub/bearing
Studs

Apply a liberal amount of anti-seize compound on the splines of the front shaft.

Insert the 2 rearmost, top and bottom rotor hub bolts in the knuckle, so they extend from the front face as shown.

Fig. Hub bolt positioning

Install or connect the following:

Spacer and shield
Hub assembly onto the shaft

Align the bolt holes in the flange with the installed bolts. Thread the bolts onto the flange far enough to hold the unit in place.

Install the remaining bolts. Tighten all hub/bearing bolts to 149 ft. lbs. (202 Nm).

Install the washer and shaft nut. Tighten the nut to 132 ft. lbs. (179 Nm). Rotate the axle 5 to 10 times to seat the bearings. Tighten the nut to 263 ft. lbs. (356 Nm). Install a new cotter pin, advancing the nut for alignment.

The remainder of installation is the reverse of removal.

These details will help.

Thanks.

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html

Ford repair professionals

Tuesday, April 24, 2012

2005 Dodge Ram Drive Belt Routing Diagrams?

Drive Belt Routings

Accessory Drive Belts Details on 2005 Dodge Ram?

Adjust Accessory Drive Belts on 2005 Dodge Ram?

Inspect Accessory Drive Belts on 2005 Dodge Ram?

Car repair guide?

Accessory Drive Belts Details on 2005 Dodge Ram?

Adjustment

Belt Tension Inspection

Car repair guide?

Suspension Wheel Hub & Bearings Replacing on 2005 Dodge RAM?

Adjustment

Removal & Installation

Car repair guide?

Infolinks In Text Ads