Accessory Drive Belts Replacing on Chevy, GMC, Yukon and Cadillac?

How to replace Accessory drive belts.
This procedure is provided here with complete details and diagrams.Accessory serpentine belt routing Diagram for - 4.3L, 4.8L, 5.3L, 6.0L and 6.2L engines.Accessory serpentine belt routing Diagram for -8.1L engines.
The procedure mentioned here is for
Cadillac Escalade, GMC Suburban 1500 & 2500, Chevy Tahoe, Yukon, Yukon XL 1500 & 2500 (2006-2007), Yukon Denali and Yukon Denali XL (2005-2006).GMC Sierra, Chevrolet Silverado 2006-2007.

The procedure to remove and replace Drive belt or serpentine belt is as follows:-----

Adjustment Procedure:


These vehicles are equipped with a single serpentine belt and spring loaded tensioner. The proper belt adjustment is automatically maintained by the tensioner, therefore, no periodic adjustment is needed. If the pointer is past the scale on the tensioner replace the belt. If correct belt tension cannot be achieved make sure the correct belt is installed. If the correct tension is still not achieved and check for proper mounting off all accessory drives.

Inspection Procedure:----

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.

Removal & Installation Procedure:---

Belt replacement is a relatively simple matter rotating the tensioner off the belt (to relieve tension) and holding the tensioner in this position as the belt is slipped from its pulley. The tensioner arm contains a machined receiver for a ³ / ₈ in. driver from a ratchet or breaker bar.

Fig. A large wrench (16mm) can be used to pivot the belt tensioner and free the belt

1. Before you begin, visually confirm the belt routing to the engine compartment label (if present) or to the appropriate diagram in this section (if the label is not present). If you cannot make a match (perhaps it is not the original motor for this vehicle), scribble your own diagram before proceeding.
2. Disconnect the negative battery cable for safety.
3. Install the appropriate sized breaker bar, wrench, or socket to the tensioner arm or pulley, as applicable.
4. Rotate the tensioner to the left (counterclockwise) and slip the belt from the tensioner pulley.
5. Once the belt is free from the tensioner, CAREFULLY rotate the tensioner back into position. DO NOT allow the tensioner to suddenly snap into place or damage could occur to the assembly.
6. Slip the belt from the remaining pulleys (this can get difficult is there is little room between the radiator/fan assembly and the accessory pulleys. Work slowly and be patient.
7. Once the belt is free, remove it from the engine compartment.

To install:

1. Route the belt over all the pulleys except the water pump and/or the tensioner. Refer to the routing illustration that you identified as a match before beginning.
2. Rotate the tensioner pulley to the left (counterclockwise) and hold it while you finish slipping the belt into position. Slowly allow the tensioner into contact with the belt.
3. Check to see if the correct V-groove tracking is around each pulley.
   
   WARNING

   Improper V-groove tracking will cause the belt to fail in a short period of time.
4. Connect the negative battery cable.

Drive Belt Routing Diagrams:-----

Accessory serpentine belt routing-4.3L engines.

 

Fig. Accessory serpentine belt routing-4.8L, 5.3L, 6.0L and 6.2L engines

 

Fig. Accessory serpentine belt routing-8.1L engines

These details will help.

Thanks.           

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html