Chrysler PT Cruiser Accessory Drive Belts Removal?

In this chapter details are provided to replace Accessory Drive Belts on Chrysler PT Cruiser.

The procedure with complete details and diagrams is as follows:----


Adjustment Details are as follows:----

Alternator Belt
The alternator belt must be adjusted manually for proper tension.

Before servicing the vehicle, refer to the Precautions Section.
Check belt tension using Special Tool 8371-Belt Tension Gauge Adapter, and the DRBIII® using the following procedures:
CAUTION
Do not check belt tension with the engine running.

Connect 8371 to the DRBIII® following the instructions provided in tool kit.
Place end of microphone probe approximately 1 in. (2.54cm) from belt at one of the belt center span locations.
Pluck the belt a minimum of 3 times. (Use your finger or other suitable object).
The frequency of the belt in hertz (Hz) will display on DRBIII® screen.
Adjust belt to obtain proper frequency (tension). Refer to the belt tension chart for specifications.
Tighten pivot bolt to 40 ft. lbs. (54 Nm) and locking nut to 40 ft. lbs. (54 Nm).
Install the power steering pump/air conditioning compressor drive belt, if removed.

Power Steering & Air Conditioning Compressor Belt
The power steering and air conditioning belt is automatically adjusted with a spring tensioner.

Inspection

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.

Removal & Installation

Alternator Belt

1. Remove the power steering pump/air conditioning compressor drive belt.
2. Loosen the pivot bolt, then the locking nut, and adjusting bolt.
3. Remove the alternator belt.

To install:

NOTE

When installing drive belt onto pulleys, make sure that belt is properly routed and all V-grooves make proper contact with pulley grooves.

1. Install belt and/or adjust belt tension by tightening adjusting bolt. Adjust belt to specification shown in Belt Tension Chart.
2. Check belt tension using Special Tool 8371-Belt Tension Gauge Adapter, and the DRBIII® using the following procedures:
   
   CAUTION

   Do not check belt tension with the engine running.
3. Connect 8371 to the DRBIII® following the instructions provided in tool kit.
4. Place end of microphone probe approximately 1 in. (2.54cm) from belt at one of the belt center span locations.
5. Pluck the belt a minimum of 3 times. (Use your finger or other suitable object).
6. The frequency of the belt in hertz (Hz) will display on DRBIII® screen.
7. Adjust belt to obtain proper frequency (tension). Refer to the belt tension chart for specifications.
8. Tighten pivot bolt to 40 ft. lbs. (54 Nm) and locking nut to 40 ft. lbs. (54 Nm).
9. Install the power steering pump/air conditioning compressor drive belt.

Power Steering & Air Conditioning Compressor Belt

1. Before servicing the vehicle, refer to the Precautions Section.
2. Remove belt splash shield.
3. Using a wrench, rotate belt tensioner clockwise until belt can be removed from power steering pump pulley. Gently, release spring tension on tensioner.
4. Remove belt.

To install:

NOTE

When installing drive belt onto pulleys, make sure that belt is properly routed and all V-grooves make proper contact with pulley grooves.

1. Install belt over all pulleys except for the power steering pump pulley.
2. Using a wrench, rotate belt tensioner clockwise until belt can be installed onto power steering pump pulley. Release spring tension onto belt.
3. After belt is installed, inspect belt length indicator marks. The indicator mark should be within the minimum belt length and maximum belt length marks. On a new belt, the indicator mark should align approximately with the nominal belt length mark.
4. Install the belt splash shield.

Drive Belt Routing Diagram:---

 

Fig. Accessory drive belt routing-2.4L engine

These details will help.

Thanks.           

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html