BannerFans.com

Wednesday, April 4, 2012

Replace Power Steering Pump on Cadillac Seville & Deville?

The procedure mentioned here is for
Cadillac DeVille, Eldorado, Seville 1999-2005 Year Car models.

In this section the procedure to replace power steering pump is mentioned and with that how to bleed power steering pump procedure is provided.


  1. Remove the drive belt.
  2. Drain the power steering fluid from the reservoir.
  3. Disconnect the return pipe from the reservoir.
  4. Remove the pressure pipe from the pump.
  5. Remove the pump mounting bolt.
  6. Remove the pump, reservoir, pulley and bracket assembly from the vehicle.
  7. Remove the pump and reservoir assembly from the bracket.
  8. Remove the pulley from the pump.
  9. Remove the retaining clips that attach the reservoir to the pump. 

    image
    Fig. Power steering pump mounting detail.
To install:
  1. Install the retaining clips in order to attach the reservoir to the pump.
  2. Install the pump and reservoir to the bracket.
  3. Install the pump to bracket bolts and tighten to 18 ft. lbs. (24 Nm).
  4. Install the pulley to the pump.
  5. Position the pump, reservoir, pulley and bracket assembly to the vehicle.
  6. Install the pump mounting bolt to the engine and tighten to 35 ft. lbs. (47 Nm).
  7. Install the pressure pipe to the pump and tighten the fitting to 20 ft. lbs. (27 Nm).
  8. Install the return hose to the reservoir.
  9. Install the drive belt.
  10. Fill the power steering system..
  11. Bleed the power steering system.
------------------
  1. Remove the serpentine belt..
  2. Drain the power steering fluid from the reservoir.
  3. Disconnect the return fluid line from the reservoir.
  4. Remove the pressure pipe from the pump.
  5. Remove the pump mounting bolt.
  6. Remove the pump, reservoir, pulley, and bracket assembly from the vehicle.
To install:
  1. Position the pump, reservoir, pulley and bracket assembly into the vehicle.
  2. Install the power steering pump mounting bolt and tighten to 37 ft. lbs. (50 Nm).
  3. Install the pressure pipe to pump and tighten to 22 ft. lbs. (30 Nm).
  4. Install the return hose to the reservoir.
  5. Install the serpentine belt.
  6. Fill the power steering system.
  7. Bleed the power steering system.
--------------------------

  1. Remove the drive belt.
  2. Install a drain pan under the vehicle.
  3. Disconnect the power steering return hose from the power steering reservoir.
  4. Remove the power steering pressure hose from the power steering pump.
  5. Remove the power steering pump mounting bolt.
  6. Remove the power steering pump from the vehicle.
  7. Remove the power steering pulley.
  8. Remove the power steering reservoir.
To install:
  1. Install the power steering reservoir.
  2. Install the power steering pulley.
  3. Install the power steering pump to the vehicle.
  4. Install the power steering pump mounting bolt and tighten to 37 ft. lbs. (50 Nm).
  5. Install the power steering pressure hose to the power steering pump and tighten to 20 ft. lbs. (27 Nm).
  6. Install the power steering return hose to the power steering reservoir.
  7. Remove the drain pan from under vehicle.
  8. Install the drive belt.
  9. Bleed the power steering system.
-----------------

Power steering Pump Bleeding Procedure:-----

  1. Use clean, new power steering fluid type only.
  2. Hoses touching the frame, body or engine may cause system noise. Verify that the hoses do not touch any other part of the vehicle.
  3. Loose connections may not leak, but could allow air into the steering system. Verify that all hose connections are tight.
    NOTE
    Power steering fluid level must be maintained throughout bleed procedure.
  4. Fill pump reservoir with fluid to minimum system level, FULL COLD level, or middle of hash mark on cap stick fluid level indicator.
  5. Raise the vehicle until the front wheels are off the ground.
  6. Key on engine OFF , turn the steering wheel from stop to stop 12 times. Vehicles equipped with hydro-boost systems or longer length power steering hoses may require turns up to 15 to 20 stop to stops.
  7. Verify power steering fluid level per operating specification.
  8. Start the engine. Rotate steering wheel from left to right. Check for sign of cavitation or fluid aeration (pump noise/whining).
  9. Verify the fluid level. Repeat the bleed procedure, if necessary.

------------

These details will help.
Thanks.           

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html


No comments:

Post a Comment